home *** CD-ROM | disk | FTP | other *** search
/ Tech Arsenal 1 / Tech Arsenal (Arsenal Computer).ISO / tek-20 / bb21c.zip / OPERATE.DOC < prev    next >
Text File  |  1992-11-12  |  16KB  |  437 lines

  1. STARTING (from a boot)
  2. ----------------------
  3.  
  4. Run MBBIOS.  It will go resident.  This step only required for OUTBOARD
  5. TNCs not using the G8BPQ Switch.
  6.  
  7. Run TNCTSR-S.  It will go resident.  This step only required if you have
  8. PC*PA card and are not using the G8BPQ switch code.  I don't supply
  9. TNCTSR-S.  Its on the diskette that comes with the card.
  10.  
  11. If you have modified PARMS.BB, run BBSETUP.
  12.  
  13. Run BBSETTNC.  This will switch your TNCs to the HOST MODE if they are
  14. not there already.  You should see one of two things for each TNC.
  15.  
  16.    * JHOST1
  17.        TNC was not in host mode but is now
  18.  
  19.    INVALID COMMAND
  20.        TNC was in host mode
  21.  
  22. For AEA TNCs with AEA NETROMS you will see
  23.  
  24.    (smiley face)OGG(blank)(two-headed arrow)
  25.  
  26. If any of these lines is not the last line for any COM ports, run
  27. BBSETTNC again.  If still no luck, check the SPEED in the PARMS.BB file,
  28. the TNC is on and ready, etc.  If after an hour or two you still can't
  29. get it to work, take two aspirin and drop me a note.
  30.  
  31. **** DO NOT PROCEED TO NEXT STEUP UNLESS BBSETUP RAN OK ****
  32.  
  33. If BBSETTNC was OK, you can now run BB
  34.  
  35.  
  36. STARTING (System has been up already)
  37. -------------------------------------
  38.  
  39. If you have modified PARMS.BB, run BBSETUP.
  40.  
  41. If you are confident that things are still in HOST MODE, you can skip
  42. running BBSETTNC but it won't hurt.  If your TNCs have been reset or are
  43. in an unknown state, then run BBSETTNC.
  44.  
  45. Now run BB.
  46.  
  47. WINDOWS
  48. -------
  49.  
  50. The screen is broken into four sections
  51.  
  52. +--------------------+
  53. |     upper          |
  54. |     window         |
  55. +--------------------+
  56. +   status line      +
  57. +--------------------+
  58. +     lower          +
  59. +     window         +
  60. +--------------------+
  61. +    input line      +
  62. +--------------------+
  63.  
  64. The status line shows the number of tasks running, the free storage, the
  65. status of the current window, and the current connected users.
  66.  
  67. The upper window can show either connected or monitor data.  The lower
  68. window shows either the operator window or the window not being shown in
  69. the upper section.
  70.  
  71. The input line shows what the operator is typing.
  72.  
  73. The current window and input line disappear if the editor is in use.
  74.  
  75. LINE EDIT KEYS
  76. --------------
  77.  
  78. These keys can be used to edit the line you are typing.
  79.  
  80.    INSERT -- Toggles insert versus overwrite mode.  Insert mode is
  81.              depicted by the large BLOCK cursor
  82.  
  83.    DELETE -- Delets the character above the cursor
  84.  
  85.    BACKSPACE -- Deletes the character to the immediate left of the cursor
  86.  
  87.    LEFT ARROW and RIGHT ARROW -- Moves the cursor one step in the direction
  88.                                  of the arror.
  89.  
  90. FUNCTION KEYS
  91. -------------
  92.  
  93. The following function keys are active at all times (except when in the
  94. editor).
  95.  
  96.       12  -- Put cursor at front of input area
  97.  
  98.       F2  -- Erase the input area from the cursor to the end of the line
  99.  
  100.       F3  -- Immediate switch to the MONITOR window.  Will disconnect
  101.             a terminal session started with "T" command
  102.  
  103.       F4  -- Clear bottom window
  104.  
  105.       F5  -- Swap monitor and connect windows between top and bottom.
  106.  
  107.       F7  -- Terminate terminal session.
  108.  
  109.       F9  -- Retrive command (clockwise)
  110.  
  111.       F10 -- Retrive command (counterclockwise)
  112.  
  113.       ALT-X -- Shutdown BBS
  114.  
  115.       Up-Arrow -- Scroll the current bottom window back one line
  116.  
  117.       Down-Arrow -- Scroll the current bottom window forward one line
  118.  
  119.       Home -- Scroll the current bottom window back to the top of the buffer.
  120.  
  121.       End  -- Scroll the current bottom window forward to the bottom of
  122.               the buffer.
  123.  
  124.       Page-Up -- Scroll the current top window back one line
  125.  
  126.       Page-Down -- Scroll the current top window forward one line
  127.  
  128.       Control-Page-Up -- Scroll the current top window back to the top of
  129.                          the buffer.
  130.  
  131.       Control-Page-Down -- Scroll the current top window forward to the
  132.                            bottom of the buffer.
  133.  
  134.       All other function keys should cause a beep and a rewrite of the
  135.       status line.
  136.  
  137. OPERATOR COMMANDS
  138. -----------------
  139.  
  140. Those available remotely have a "*".  If you are on remote, you must
  141. issue the appropriate "@" command to switch to remote sysop mode before
  142. using anything but the "@" command.  Note that all commands are
  143. available via WAKEUP
  144.  
  145.  *   @  -- Change to remote SYSOP
  146.  *   @N -- Change to new user
  147.  *   @U -- Change to unregistered user
  148.  *   @O -- Change to user
  149.  *   @E -- Change to expert
  150.  *   @B -- Change to BBS
  151.  *   @R -- Change to remote SYSOP (same as @)
  152.      @L -- Change to local SYSOP
  153.  
  154.  *   A  -- Reload the action file and execute all actions
  155.  
  156.  *   AC -- Execute CLEAN actions only
  157.  
  158.  *   AF -- Reload the action file and execute MAKE_FILE actions
  159.  
  160.  *   AL -- Reload the action file
  161.  
  162.  *   AM -- Execute MAKE_FILE actions only
  163.  
  164.      B  -- Closes the operator window (same as F3)
  165.  
  166.  *   C  xxxxx -- Set the system clock.  xxxx is the date/time in format
  167.            of YYMMDDHHMM.  If the command "C" alone is given, the system
  168.            responds with its date/time
  169.  
  170.  *   CF file1 file2 -- Copies a file.  Can also be used to print a file.  To
  171.            print, use LPT1 or LPT2 as file2.
  172.  
  173.  *   CLOSE port -- Prevents any future forwarding or connects on the port.
  174.            Users receive message # 167.  Port should be either the letter
  175.            of the port or "S" for system.
  176.  
  177.  *   CM msgno address -- Copy message "msgno" to "address."  You can also
  178.            add news bids if necessary.  Example:
  179.                   CM 1234 W0RLI @ W0RLI
  180.            The old bid will be used unless specified otherwise.  You should
  181.            either expressly code a new bid or ask for a generated on by
  182.            using just the "$".  Example:
  183.                   CM 1234 W0RLI @ W0RLI $
  184.  
  185.  *   DC -- Display routes.  Shows all active routes and the number and
  186.            type of messages waiting for them
  187.  
  188.  *   DR -- Display routes.  Shows all active routes and the messages
  189.            waiting for them
  190.  
  191.  *   DR call -- Display routes for this call only.  Call can be a wildcard
  192.            string such as WB6*
  193.  
  194.  *   DU -- Display users
  195.  
  196.  *   DU call -- Display a particular user
  197.  
  198.  *   EC port -- Edit control parameters for a port.  See MODE.DOC
  199.            Port should be either the letter of the port or "S" for
  200.            system.
  201.  
  202.      EF filename -- Edit a file.  Uses BORLAND's BINARY EDITOR (part of
  203.            the TURBO PASCAL Editor toolbox).  See EDIT.DOC for details
  204.  
  205.  *   EL -- Same as EL but will automatically do a GL after the server runs.
  206.  
  207.  *   EM msgno -- Edit a message's header
  208.  
  209.  *   EP port -- Edit parameters for a port.  Same format as EC
  210.  
  211.  *   ES [options] server file parms -- Execute a server.  Example:
  212.                           ES REQDIR D:\PATH\T17.EXE
  213.                           ES REQFIL DOS BATNAM
  214.                           ES REQDIR [K] D:\BB\T21.EXE
  215.            Use the second example for DOS commands and BAT files.  See info
  216.            in SERVER.DOC.
  217.  
  218.      ET msgno -- Edit text of a message.  Uses same program as EF
  219.  
  220.  *   EU call  -- Edit a user's information (See USER.DOC)
  221.  
  222.  *   EX [options] file parms -- Execute another program.  Example:
  223.                           EX D:\PATH\T17.EXE
  224.                           EX DOS BATNAM
  225.                           EX [EK] D:\BB\T21.EXE
  226.            Use the second example for DOS commands and BAT files.  See info
  227.            in SERVER.DOC
  228.  
  229.  *   EXPORT [options] filename # message_list -- EXPORT to a file the
  230.            messages indicated.
  231.  *   EXPORT filename {search}  -- Export files who match a search.
  232.  
  233.            If the file exists, the messages are appended to it.  EXPORTK
  234.            instead of EXPORT means kill message after export.
  235.  
  236.            [options] are:
  237.  
  238.               H - add header when exporting
  239.               K - Kill message after export.
  240.  
  241.            Examples:
  242.                     EXPORT A:A # 124 3465 22
  243.                     EXPORT [H] A:A > GONZO
  244.  
  245.  
  246.  *   EW -- Send any white-pages updates
  247.  
  248.  *   Fx msgno directory filename -- Make file from message.  Directories
  249.            are those shown by W. If the command is just F, then include
  250.            the X400 header.  If the command is FH, give the X400 header
  251.            but show all BBS route headers.  If the command is FN, copy
  252.            message asis.  Can also be used to print a message.  To print,
  253.            use LPT1 or LPT2 as directory and omit the filename.
  254.  
  255.  *   FORCE task -- Issue an immediate disconnect to the indicated task.
  256.            To force a user, get his task name from the status line.
  257.                     Example: FORCE B3
  258.  
  259.      GB -- Set the SYSOP bell flag. 1 or Y is on.  0 or N is off.  If
  260.            nothing specified then the flag will be flipped.
  261.  
  262.  *   GC window filename -- Capture all new lines written to a window to
  263.            a file (or printer).  The window name must be OPERATOR,
  264.            CONNECT, or MONITOR.  If the file already exists, then the data
  265.            is added on the end.  To terminate, issue GC with no parms.
  266.  
  267.  *   GE -- Load a new message text file (usually MESSAGE.BB)
  268.  
  269.  *   GF -- Tell BB that ROUTE.BB had been changed.
  270.  
  271.  *   GH -- Do a lookup for extended addresses.  Command will normally
  272.            resume where it left off.  GH 1234 will foce the lookup to
  273.            start at message 1234.
  274.  
  275.  *   GI -- Reorganize BID file
  276.  
  277.  *   GK -- Force a wakeup cycle.  Used to tell BB that WAKEUP.BB has
  278.            been changed.
  279.  
  280.  *   GL -- Reload the regular message file.
  281.  
  282.  *   GM -- Reorganize the message file.  Will not run if anyone else is
  283.            connected or if forwarding is in progress.  Killed files
  284.            actually disappear now.
  285.  
  286.  *   GN xxxx yyyyy -- Change a file name. xxxx is the file you want to
  287.            change.  Allowed are: PATH, ROUTE, MESSAGE, WAKEUP, HELP,
  288.            HLOOKUP, PASSWORD, ACTION.  yyyyy is the name of the new file.
  289.            Example:
  290.  
  291.                  GN ROUTE \ROUTE.NEW
  292.  
  293.  *   GO -- Mark messages as old.  You can mark messages by bid or by age.
  294.  
  295.               GO BID pattern -- Marks a message old by matching its BID
  296.                                 to a pattern.  See WILDCARD.DOC for
  297.                                 pattern info.  You can have multiple
  298.                                 patterns.
  299.  
  300.               GO TYPE msg_type age -- Mark a message old is its type
  301.                                 matches and it is more than "age" days old.
  302.  
  303.                                 Example:
  304.                                    GO TYPE B 15 PT 3 * 5
  305.  
  306.                                    Mark B messages after 15 days, P or
  307.                                    T messages after 3 days and all others
  308.                                    after 5 days.
  309.  
  310.               GO {search} -- Marks a message old that matches the given
  311.                                 search. See SEARCH.DOC
  312.  
  313.      GP -- Set the flag that supresses showing the prefix area.  1 or Y is
  314.            on.  0 or N is off.  If nothing specified then the flag will be
  315.            flipped.
  316.  
  317.  *   GR -- Same as GM but renumber messages too.  Will restart at 1.
  318.                    GR 1234 will start renumbering at 1234.
  319.  
  320.      GS -- Set the sysop available flag.  1 or Y is on.  0 or N is off.  If
  321.            nothing specified then the flag will be flipped.
  322.  
  323.  *   GW window filename -- Capture the current contents of a window to
  324.                    a file (or printer).  The window name must be
  325.                    OPERATOR, CONNECT, or MONITOR.  If the file already
  326.                    exists, then the data is added on the end.
  327.  
  328.      GZ -- Set the show error during forward script flag.  1 or Y is
  329.            on.  0 or N is off.  If nothing specified then the flag will be
  330.            flipped.
  331.  
  332.  *   HOLD {search} -- Change messages to hold status.  You can use the
  333.              same syntax as "R".  Examples:
  334.  
  335.                              HOLD 123 TO 126
  336.                              HOLD 123 146 156
  337.  
  338.  *   IMPORT filename -- IMPORT from a file
  339.                     IMPORTE instead of IMPORT means erase file when done.
  340.  
  341.  *   K{search} -- Kill messages who match a search (See SEARCH.DOC for
  342.                   details).  Some useful examples:
  343.                        KH -- Kill all held files
  344.                        KO -- Kill all old files
  345.  
  346.  *   KILL task -- Issue an immediate disconnect to the indicated task
  347.            and then destroy the task without waiting for the TNC
  348.            To kill a user, get his task name from the status line.
  349.                     Example: KILL B3
  350.  
  351.  *   L{search} -- List messages who match a search (See SEARCH.DOC for
  352.                   details).  Some useful examples:
  353.                        LH -- List all held files
  354.                        LO -- List all old files
  355.  
  356.  *   Mc filename address -- Make message from file.  Message class is "c".
  357.            File name is fully qualified.  Address is who to send it to.
  358.            You can also add BIDS.  Example:
  359.  
  360.                              MB a:bbb ALL @ ALLCA
  361.  
  362. *    OPEN port -- Reverses action of CLOSE command.  Port should be either
  363.            the letter of the port or "S" for system.
  364.  
  365.      QUIT -- Immediate stop (not safe.  Use only in emergencies)
  366.              Files will not be closed nor will disconnects be issued.
  367.  
  368.  *   REL {search} -- Release messages from hold and review.  You can use the
  369.              same syntax as "R".  Examples:
  370.  
  371.                              REL 123 TO 126
  372.                              REL 123 146 156
  373.                              REL H
  374.  
  375.              The last example will release all messages in hold.
  376.  
  377. *    REVIEW {search} -- Display messages for review.  If search is not
  378.              specified then "V" is assumed.  Each message is displayed and
  379.              SYSOP is asked to tell what should be done.  Options are
  380.              Kill, Leave, Release, Hold, and Quit.  The last action leaves
  381.              the message untouched and terminates the review command.
  382.              Remote SYSOPs indicate the action by typing the first letter
  383.              of the word.  Local SYSOPs indicate the action by pressing
  384.              ALT-x where x is the letter of the action to be taken.
  385.              Local SYSOPs see the messages in the full screen editor with
  386.              the title line showing on the top line of the box.
  387.              Uses same program as "EF" and "ET."  See EDIT.DOC
  388.  
  389.  *   SHUT -- Shuts BBS down but only if not busy.  Same as ALT-X
  390.              See WAKEUP.DOC for precautions to take when using this
  391.              command in a wakeup file.
  392.  
  393. *    SHUTNOW -- Shuts BBS down.  Same as ALT-X See WAKEUP.DOC for
  394.              precautions to take when using this command in a wakeup file.
  395.  
  396.      T portchan -- Talk to indicated portchan.  Puts the operator
  397.                    in terminal mode.  All WA8DED commands are available.
  398.                    To leave, use either F3 or F10.  See TERMINAL.DOC
  399.  
  400.  *   UNKILL {search} -- Change messages from kill status.  You can use the
  401.              same syntax as "R".  Examples:
  402.  
  403.                              UNKILL 123 TO 126
  404.                              UNKILL 123 146 156
  405.                              UNKILL K
  406.  
  407.              The last example will "unkill" all killed messages.
  408.  
  409.  *   X -- Start foward now
  410.  
  411.  *   X PORT p -- Start forward to a port now.  p can be a single port
  412.              letter or a sub-port designation
  413.  
  414.  *   X path  -- Start forward to a path now
  415.  
  416.  *   X path FORCE -- Start forward to a path and connect even if no messages.
  417.                      FORCE can be combined with CONNECT.
  418.  
  419.  *   X path CONNECT -- Start forward to a path and connect even if already
  420.                        connected on another path.  CONNECT can be combined
  421.                        FORCE.
  422.  
  423.  *   XSTOP -- Force current forward cycle to end.  MUST BE IN CAPS!
  424.  
  425.  *   Z directory filename -- Erase file in a directory
  426.  
  427.  
  428.  
  429. REMOTE SYSOP PASSWORDS
  430. ----------------------
  431.  
  432. Now moved to AUTHENT.DOC.
  433.  
  434. The password will be prompted when the @R command is issued.  Modem users
  435. will not need a remote sysop password.
  436.  
  437.